*TESTING THE SURFACE BEFORE FULL APPLICATION IS ALWAYS PARAMOUNT!

COVERAGE

Application losses may vary according to surface substrate and the method of application and is always  taken into account when estimating the quantity of product needed.
 

PRECAUTION

Observe all labels, MSDS, and instructions before using this product and equipment. Protect your health! Provide adequate ventilation in working area. When working with NiGHTSHiNE NiGHTLiNE, it is strongly suggested to wear safety clothing, gloves, and safety goggles. A full face shield is also recommended. Spills and blow-outs do happen! Consider persons and property in proximity to the application area to prevent damage or injury.

# Store all materials and equipment safely out of the reach of children.

# Refer to MSDS sheets for instructions if material comes in contact with eyes or skin.
 

MAINTENANCE OF EQUIPMENT

For any cartridges that have been opened but not used up, do not remove the static mixer. Store the cartridge with the static mixer attached. The NiGHTSHiNE NiGHTLiNE inside the static mixer will cure and protect the cartridge. The static mixer can be removed and replaced with the next application.

Cartridges and static mixers are disposable. Dispose in accordance with current applicable local, state and federal regulations. Tools and equipment are best cleaned immediately after use. Acetone may be used to clean tools and equipment.
 

STORAGE

Store indoors, best storage stability of cartridges at temperatures 70-85 F. For best results store cartridges horizontally.
 

NOTE

The data contained herein is furnished for information only and is believed to be reliable. We cannot assume responsibility for the results obtained by others over whose methods over which we have no control. It is the user’s responsibility to adopt such precautions for the safety of property and persons.
 

APPLICATION

All site work and applications are done using our fully trained and pre-qualified installers.

Depending upon the site requirements, layout and in particular access there are a number of processes and equipment that we use.

For stairs and landings in Fire Escapes for example we can use either a masking tape or a Polypropylene stencil which we design and manufacture for the site using laser profiling to ensure dimensional standards [which are critical for safety egress systems] are maintained during installation throughout the site.

For more 'open areas & sites' such as walkways, hallways and path marking systems in hospitals, nursing homes, commercial and industrial complexes office buildings, warehouse, train and bus stations etc a number of application systems are available.

MASKING TAPE:

STEP ONE:

We place masking tape on the surface area where NiGHTSHiNE NiGHTLiNE is to be applied. Use firm pressure when applying tape to assure that you have good contact with the surface area, this will help to eliminate the primer or NiGHTSHiNE NiGHTLiNE from traveling under the tape.  (A laser line will aide to make straight lines)
 

STEP TWO

Our "Primer" is always applied to the surface area before the application of NiGHTSHiNE NiGHTLiNE. We apply primer to the surface area between tapes and allow primer to dry completely. Depending on the substrate it may be necessary to apply two light coats rather the one thick coat.
 

STEP THREE

Prepare NiGHTSHiNE NiGHTLiNE Cartridge: Load NiGHTSHiNE NiGHTLiNE cartridge into dispenser gun. Remove the cap from cartridge. Dispense a small amount of material until both components flow out equally. Install the static mix tube into cartridge and dispense a quarter size of material onto waste paper. This will insure we have a proper mix of material before you begin to apply NiGHTSHiNE NiGHTLiNE.
 

STEP FOUR

Dispense material as required to meet the dimensional requirements of the marking down the middle of the tape.
 

Note the majority of our applications are normally completed using a mechanical system but again depending on site requirements some applications may be done manually as shown above applying primer and below applying top coat;

STEP FIVE

After the material has been dispensed between the stencil tapes, the stencil tape can be removed immediately. Do not wait more than 2 minutes to remove the stencil tape. Remove one side of the stencil tape at a time, pulling the stencil tape towards the centre of the strip. This will keep the material from spreading outward from the centre.
 

The NiGHTSHiNE NiGHTLiNE  is cured for use once it is dry to the touch and a fingernail impression is hard to make. For a area of general use it is advised to block the area off for 4 hours.

For an area of high traffic it is advised to block off the area for 8 hours. These times may vary depending on ambient temperature.
 

CLEAN UP

• Any unused material left in the cartridges may be stored for future use.
• Do not remove the static nozzle, the material in the static nozzle will cure and protect the cartridge.
• Replace the static nozzle upon the next use.
• It is best to store cartridge horizontally.
• Used cartridges and static nozzles are disposable.
• Dispose in accordance with current applicable local, state and federal regulations.
• Tools and equipment are best cleaned immediately after use.
• Use acetone to clean tools and equipment, uncured material may be wiped up with a clean cloth.
• × Do not use solvents.
 

OUR EQUIPMENT IS- 100% Australian Owned and Manufactured

Technical Information:

Note: Product and Material Safety Data information is available and supplied to customers as part of our quoting, sales and application procedures.

Due to the upcoming launch of our NEW 'state of the art' NEXT GENERATION PRODUCTS some technical information is currently not available.

 

THE NiGHTSHiNE AUSTRALIA GROUP WORLD LEADERS IN PHOTOLUMINESCENT TECHNOLOGY & SAFETY EGRESS SYSTEMS

HEAD OFFICE: Gold Coast - Queensland - Australia

Copyright © 2007 - NiGHTSHiNE Australia    All material and content remains the property of the NiGHTSHiNE and may not be used without permission or consent of the publisher.